YEELIGHT
YEELIGHT Staria Bedside Lamp Pro Wi-Fi
SKU: YEELYLCT03YL
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Effortless lighting, wireless charging. Charge your phone wirelessly at any time.
Yeelight Staria Bedside Lamp Pro can charge your phone and AirPods wirelessly. The combination of a 10W wireless charging module and an efficient heat dissipation aluminum sheet allows for charging in a much shorter time.
The right light for the right mood.
Calibrated with a proprietary algorithm based on the Kruithof curve, Staria Pro offers just the right brightness and color temperature to create the desired ambiance.
"Hey Siri, turn on the lights!"
You can simply control your lights with Apple’s Home App or voice control on your iPhone, iPad, HomePod, Apple Watch, and Mac.
Create your own scenarios by integration with HomeKit products.
You can connect Staria Pro with the global network of HomeKit smart devices to create a fully connected smart home. Just let your innovation shine.
Enjoy the ease of smart lighting control.
You can also integrate the lamp with smart system, such as Google Assistant, Amazon Alexa, Apple HomeKit and SmartThings or to remote control your lamp with APP. Feel free to use your imagination to add more personal touches to your everyday life.
Simple control with one touch.
With easy adjustment of brightness and color temperature, your desired ambiance is just one touch away.
Sleek design radiating pure glamor.
With simple styling and smooth lines and the striking star ring on the back, Staria Pro rounds off an aesthetically appealing environment. You will find it a great addition to any home of any style.
More pure and uniform lighting.
The shade is specially made of PC materials to help diffuse the light and direct it down where you need it.
Non-slip silicone feet | Keeping the lamp firmly in place.
A hidden 30° spindle | Balancing beauty with functionality.
Supported models for wireless charging.
- Apple: iPhone 8, iPhone 8 Plus, iPhone X, iPhone XR, iPhone XS, iPhone XS MAX
- Samsung: S7, S8, S9, S10, S10+
- HUAWEI: Mate20 Pro, P30 Pro
- Google: Pixels 3, Pixels 3L
- LG: G7, G8, V30, V30+, V35, V4 ThinQ, V50
- SONY: Xperia XZ2, Xperia XZ2 Premium, Xperia XZ3
Features:
- Product Name: Yeelight Staria Bedside Lamp Pro
- Model Number: YLCT03YL
- Color: White
- Size: 179.5×179.5×292.5 mm
- Rated Power: 20 W
- Voltage: 220–240 V ~ 50/60 Hz
- Power Supply: Adapter DC 12 V 1.5 A
- Adapter Size: Ø 4.0 mm, L 150 cm
- Operating Temperature: -10 °C to +35 °C
- Luminous Flux (Brightness): 35–350 lm, adjustable
- Color Temperature: 2700–6000 K, adjustable
- IP Code: IP20
- Color Rendering Index (CRI): ? 90
- Thickness of Smartphone Case: ? 3.5 mm (when charging phone on the pad)
- Lifetime: ? 25,000 h
- Number of Switch Cycles (On/Off): > 12,500
- Warm-Up Time to 60% Light: Instant full light
- Power Source: Adapter DC 12 V 1.5 A
- Compatible with Android 4.4 (or higher) & iOS 8.0 (or higher)
- Wireless Connection: WLAN IEEE 802.11 b/g/n 2.4 GHz
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.1800000x0.3000000x0.1800000 mm |
| Weight | 1055 gr |
| EAN | 6924922218036 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.