TESLA Smart Home
TESLA Smart Home Smart Button Zigbee
SKU: TSLZSEN-BUTTON
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
This is the button TESLA Smart Home Smart Button and it will change your life. Something that can solve almost every problem you have. One button, one click and no worries.
Long Life.
As it"s a battery-powered device, you can place it anywhere you like. And since it"s very energy-efficient, it lasts up to two years without you having to replace the battery.
Perfect Range.
The ZigBee protocol used by TESLA smart devices allows a range of up to 50 m. What"s more, the entire system is very stable, so it will never let you down.
Voice Commands.
You can also control the device with your voice. All you need is the app on your phone and one of the personal assistants – Google Assistant or Amazon Alexa. They"ll then pass your wish to the device itself.
Zigbee protocol.
The product belongs to a group that uses the ZigBee protocol by which the products communicate with each other. For the proper functioning of these products, it is necessary to have the TESLA Smart ZigBee Hub central unit as part of the smart home. This creates a common network for these products and allows them to interact with each other. For example, if the humidity sensor detects an increased value, it will automatically notify the dehumidifier via the Tesla Smart ZigBee Hub, which will start.
It will do anything for you.
Having a smart home button TESLA Smart Sensor Button is like having a handy helper for each of your worries and household tasks that can do everything for you. So set it up as you wish and need.
Set it up as you please.
The device only needs one battery to operate, which lasts up to one year thanks to energy saving.
Easy use.
The button TESLA Smart Sensor Button can control its smart home companions very easily. This is thanks to the ZigBee protocol. This technology connects smart devices and allows them to communicate with each other. Everything can also be controlled by the smart personal assistants Amazon Alexa and Google Assistant.
Features:
- Smart Button Zigbee
- ID: TSL-SEN-BUTTON
- Battery State Monitoring: Yes
- Power Supply: 1x button cell CR2032
- Operating Temperature: -10?55 °C
- Dimensions: Ø50 x 16 mm
- Connectivity: Zigbee
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0500000x0.0500000x0.0160000 mm |
| Weight | 23 gr |
| EAN | 8596115811010 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.