Aeotec
Aeotec Water Sensor 8
SKU: AEOEZWA056
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
***PRE-ORDER possible***
Water leaks are among the most underestimated household dangers.
They often go unnoticed until significant damage has already occurred. The Aeotec Water Sensor 8 monitors areas that are out of sight, detects leaks early, and alerts you immediately. Whether it’s a leaking washing machine, a faulty pipe, or unnoticed moisture on the floor – the sensor helps you prevent costly water damage and protects what matters most: your home.
With fast detection and reliable monitoring, the Water Sensor 8 gives you peace of mind before small issues turn into major problems.
More than just a leak detector – A smart climate sensor for your well?being
- Precise temperature monitoring
Continuously tracks indoor temperature to ensure comfort and stable living conditions. - Accurate humidity tracking
Reliably measures humidity levels to support a healthy indoor climate and prevent moisture-related issues. - Mold risk notifications using a dew?point algorithm
Analyzes temperature and humidity via dew?point calculation to warn you early about potential mold growth. - Universal binary input for third?party sensors
The probe of the Aeotec Water Sensor 8 can be used as a dry?contact binary input, enabling seamless integration with a wide range of external sensors, such as:- Reed contacts
- Alarm systems
- Smoke detectors
The open/closed status of these devices can be read directly by the Water Sensor 8. This allows you to monitor external sensors in one unified system, expand your smart home capabilities, and eliminate the need for additional hardware.
Engineered for precision and practicality
The Water Sensor 8 combines elegant design with smart functionality. Its mounting plate allows easy installation anywhere in your home, while the built?in tamper protection ensures it stays securely in place.
With its 5V USB?C port, the device can operate continuously without battery replacements.
The flexible probe extension allows precise positioning and can be replaced with any compatible water?sensor probe using a 2.5 mm audio jack. This gives you maximum adaptability for any installation environment.
Outstanding range. Uncompromising reliability.
Thanks to Z?Wave Long Range, the Water Sensor 8 delivers highly reliable communication even in large homes.
Its extended wireless coverage surpasses traditional smart?home protocols, reducing dead zones and maintaining a strong connection across floors, walls, and long distances.
Combined with extremely low power consumption, Z?Wave Long Range provides:
- stable performance
- longer battery life
- a more responsive smart?home environment
This makes it an ideal foundation for secure door and window monitoring and other safety?critical applications.
Technical Specifications:
- Product dimensions: 70 × 18 × 19 mm
- Z?Wave chip series: 800 (EFR32ZG23)
- Z?Wave version: Z?Wave Plus Long Range
- Power supply:
- Battery (1× CR14250, 3 V, 1500 mAh)
- or 5 V USB?C
- Sensor functions:
- Water (binary input)
- Temperature: –10 °C to 60 °C (±1 °C)
- Humidity: 0–80 % RH (±3 %)
- Dew?point calculation
- Mold risk notification
- Operating temperature: 0 °C to 70 °C
- IP rating: IP20
- Battery life: approx. 4 years with 1× CR14250
- Range:
- Mesh network: up to 200 m (open field)
- Long Range network: up to 1.6 km (open field)
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| EAN | 1220000017436 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.