Zooz
Z-Wave Relay Dimmer switch
SKU: ZW34
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
This product is a Z-Wave multi-channel device.With dimming and relay two different functions. Built-in S2 security encryption
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
| 2 | 5 | basic set command |
| 3 | 5 | basic set command |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: LED Indicator Mode for Dimmer
LED Indicator Mode for Dimmer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | On when off and off when on |
| 1 | On when on and off when off |
| 2 | Alwaysoff |
| 3 | Alwayson |
Parameter 10: Auto Turn-Off Timer for Relay
Auto Turn-Off Timer for Relay Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | The countdown time, the Relay off |
Parameter 11: Auto Turn-On Timer for Relay
Auto Turn-On Timer for Relay Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | The countdown time, the Relay on |
Parameter 12: Restores state after power failure
Restores state after power failure Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 | dimmer, relay off |
| 1 | dimmer off, relay on |
| 2 | dimmer on, relay off |
| 3 | previous state for dimmer, previous state for relay |
| 4 | previous state for dimmer,relay on |
| 5 | previous state for dimmer,relay off |
| 6 | dimmer on, previous state for relay |
| 7 | dimmer off, previous state for relay |
| 8 | dimmer on, relay on |
Parameter 13: Ramp rate
Ramp rate (local button only, remote control by command class) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 99 | from 0x63 to 0x00 or from 0x00 to 0x63 need Required time |
Parameter 14: Multilevel minimum value can be set
Multilevel minimum value can be set Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 99 | The minimum brightness of a dimmer |
Parameter 15: Multilevel maximum value can be set
Multilevel maximum value can be set Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 0 - 99 | The maximum brightness of a dimmer |
Parameter 17: when switch is on or off and quickly press UPPER paddle 2 times,
when switch is on or off and quickly press UPPER paddle 2 times, switch turns on to x brightness Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | turn on to 99 |
| 1 | turn on to the value relate with parameter 15 |
Parameter 18: Double Tap Behavior
Double Tap Behavior Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | enable double tap to full brightness, single tap to last brightness level or custom value set in parameter 23 |
| 1 | disable double tap to full brightness, single tap to last brightness level or custom value set in parameter 23 |
| 2 | isable double tap to full brightness, single tap always to full brightness |
Parameter 19: Enable or Disable local / Z-Wave control for DIMMER
Enable or Disable local / Z-Wave control for DIMMER Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable local on/off control |
| 1 | enable local and Z-Wave control (normal operation like now) |
| 2 | disable local and Z-Wave on/off control |
Parameter 2: LED Indicator Mode for Relay
LED Indicator Mode for Relay Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | On when off and off when on |
| 1 | On when on and off when off |
| 2 | Always off |
| 3 | Always on |
Parameter 20: Enable or Disable local / Z-Wave control for RELAY
Enable or Disable local / Z-Wave control for RELAY Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable local on/off control |
| 1 | enable local and Z-Wave control (normal operation like now) |
| 2 | disable local and Z-Wave on/off control |
Parameter 21: Dimmer Speed Setting (only for local press & hold)
Dimmer Speed Setting (only for local press & hold) Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 0 - 99 | Time required for local key dimming |
Parameter 22: Ramp rate for Z-Wave on/off controlled
Ramp rate for Z-Wave on/off controlled Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | on/off ramp rate for Z-Wave same as manual control (set in Parameter 13) |
| 1 | on/off ramp rate for Z-Wave control set through command class (like now) |
Parameter 23: default brightness level
Default brightness level - in this parameter define default brightness level Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 99 | in this parameter define default brightness level |
Parameter 3: LED Indicator Color for Dimmer
LED Indicator Color for Dimmer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | White |
| 1 | Blue |
| 2 | Green |
| 3 | Red |
Parameter 4: LED Indicator Color for Relay
LED Indicator Color for Relay Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | White |
| 1 | Blue |
| 2 | Green |
| 3 | Red |
Parameter 5: LED Indicator Brightness for Dimmer
LED Indicator Brightness for Dimmer Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Bright(100%) |
| 1 | Medium(60%) |
| 2 | Low(30%) |
Parameter 6: LED Indicator Brightness for Relay
LED Indicator Brightness for Relay Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Bright (100%) |
| 1 | Medium (60%) |
| 2 | Low (30%) |
Parameter 7: LED Indicator Mode for Scene
LED Indicator Mode for Scene Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Enable |
| 1 | Disable |
Parameter 8: Auto Turn-Off Timer for Dimmer
Auto Turn-Off Timer for Dimmer Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | The countdown time, the Dimmer Off |
Parameter 9: Auto Turn-On Timer for Dimmer
Auto Turn-On Timer for Dimmer Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | The countdown time, the dimmer on |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 2 FW: 1.00 |
| Z-Wave Version | 6.82.00 |
| Certification ID | ZC10-20016827 |
| Z-Wave Product Id | 0x0312.0xa000.0xa008 |
| Firmware Updatable | Updatable by Consumer by RF |
| Switch Type | Push Button |
| Color | White |
| Electric Load Type | Dimmable LEDFluorescentIncandescentInductive (e.g. Motor) |
| Security V2 | S2_UNAUTHENTICATED |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Basic V2
- Central Scene V3
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Multi Channel Association V3
- Multi Channel V4
- Powerlevel
- Security 2
- Supervision
- Switch Binary
- Switch Multilevel V4
- Transport Service V2
- Version V3
- Zwaveplus Info V2
Controlled Command Classes
- Basic V2
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.